Design of Submarine Pipelines Against Upheaval Buckling
This paper describes part of a comprehensive joint-industry project on upheaval buckling. It develops a semi-empirical simplified design method and detailed design methods based on a new numerical analysis,...
Spread Footings Revisited: Geotechnical Advances Lead to Expanded Use for Bridge Abutments
The Minnesota Department of Transportation (MnDOT) has historically used steel shell piles to support highway bridge structures, probably due to a blend of familiarity and efficiency among...
Screw Piles and Helical Anchors: 180 Years of Use in Geotechnical Engineering
Since 1836, screw piles and screw cylinders have been used successfully throughout the world to support a variety of large-scale, civil engineering structures. Their development and use...
Long-Term Performance Monitoring of a Hillside Retaining Wall
To accommodate expansion of the West Point Treatment Plant in Seattle, WA, a 3,000-ft-long soldier pile, tieback-anchored retaining wall was constructed from May 1991 to May 1992. An oblique...
Scope
This standard guideline covers planning, design, pipe materials, and construction of microtunneling. The term microtunneling is defined as a trenchless construction method for installing...
Project Layout
Microtunneling projects should be laid out with attention to the benefits and constraints unique to this construction process. The following recommendations address some of these concerns:...
Shaft Considerations
Jacking and receiving shaft locations should be selected to minimize the number of shafts and disruptions while not exceeding the practical limits of the drive lengths achievable for a...
Pipe Characteristics
Microtunneling pipe should meet the following general requirements: Circular shape with a flush outside surface (including at the joints); Strength sufficient to withstand both the installation...
Pipe Design
The pipes and joints, once installed, must be capable of safely withstanding, for the project design life, all in-use service loads, including those associated with the following factors:...
Field Aspects
As soon as practical after their arrival at the project site, all pipes, fittings, and appurtenances should be thoroughly checked for compliance with the contract documents and accepted...
Shafts/Temporary Structures
Shafts should be of a size to accommodate the equipment and pipe selected and to allow for safe working practices. If the shaft must accommodate the permanent works, it is the contractor's...
Performance Limits for Deepwater Pipelines
This paper highlights the differences between onshore and offshore pipeline design. It then summarizes the results of combined external pressure, tension, and bending testing on full scale...
A Simple Model to Predict Soil Resistance to Driving for Long Piles in Deepwater Normally Consolidated Clays
As the exploration and development for offshore oil and gas reserves moves into the deepwater environment of the continental slope, a good model is necessary to evaluate drivability of...
Axial Load Capacity of Pipe Piles in Sands
The axial load capacity of driven, open-ended, steel pipe piles in cohesionless soils, is often estimated using a method such as the American Petroleum Institute Recommended Practice 2A...
Behaviour of Open-Ended Pipe Piles in Sand During Installation and Loading
An experimental study was performed to investigate the physical processes which influence the axial load capacities of open-ended steel pipe piles in sand. A double-walled pipe pile was...
Pile-Driving Formulas for Friction Piles in Sand
Dynamic pile-driving formulas are widely used in predicting the load-carrying capacity of friction piles and in writing pile-driving specifications. Further, when load tests are available,...
Axial Capacity of Steel Pipe Piles in Clay
Development of theories for the prediction of the axial compressive and tensile load capacities of driven piles is made difficult by a variety of factors, e.g., disturbance of the soil...
Offshore Technology in Civil Engineering
Hall of Fame Papers from the Early Years
Prepared by the Program Committee of the Offshore Technology Conference of the Coasts, Oceans, Ports, and Rivers Institute of ASCE. This series presents...
Application of Model Pile Tests to Axial Pile Design
Experiments conducted with instrumented model pile segment probes at Harvey and Empire, Louisiana are summarized and the observed behavior interpreted. Correlations are developed for the...
Case Study of Offshore Pile System Reliability
This paper presents the results of research effort to evaluate the reliability of offshore pile foundation systems. It is an extension of previous work by the authors [14] dealing with...
Return to search